call OR WHATSAPP usa / UK
+1 7045936635 | +44 7501453956
EasyFlex Pro All-in-1 Panel Stand
EasyFlex is the Pro Series evolution of the original Flexible stand design, developed to improve ergonomics, protect the turning mechanism and increase workflow flexibility in modern bodyshops.
Best suited for
- Shops that want one stand to cover most day-to-day panels without switching equipment
- Technicians who care about posture and want to reduce bending and awkward reach
- Workshops where floor space is tight and stands need to be stored flat
Single Panel Stand
Single Panel Stand: Quick Fit Check
Best suited for
- High-volume shops painting panels primarily in a vertical position
- Workflows where speed and simplicity matter more than rotation or tilt adjustment
- Teams wanting multiple economical stands to run several panels at once
In daily use
- Fast to mount and remove panels with minimal setup steps
- Holds panels upright for straightforward spraying and curing
- Designed for moving panels into the booth and through curing without complex adjustments
- Available base options support either flat storage or stacking (depending on configuration)
Overview
The Flexible Single Panel Stand is a simple, fixed-position panel stand primarily used for spraying and curing panels in a vertical or near-vertical orientation.
It is designed for practical day-to-day collision repair where a shop wants a fast, reliable stand without the additional adjustment mechanisms found on multi-process rotating stands.
Workflow Positioning
Within the Flexible Workflow System, the Single Panel Stand supports narrow vertical panels such as fenders and smaller door sections during preparation and paint work. Its role is to stabilise these panels so technicians can work efficiently without repeatedly repositioning the part.
Flexible Small Parts Module System
The Single Panel Stand is compatible with the Flexible Small Parts Module System. Modules such as the Flexible SnapGrip Module and Flexible Double Magnetic SnapGrip Module allow technicians to mount mirrors, trim and other small components alongside vertical panels.
This modular compatibility allows multiple component types to be processed within the same workstation while maintaining stable positioning during preparation and paint work.
Simple Fixed Position Workflow
Because the stand does not use a turning and locking mechanism, it is quick to deploy and easy to operate. This suits workflows where panels are painted in a consistent upright position and the technician does not need frequent angle changes.
This makes it a strong choice for shops processing many similar jobs, where speed and repeatability matter.
Best Use Cases
The stand is ideal for panels that are typically sprayed upright, and for workshops that prefer straightforward equipment with minimal moving parts.
It is generally not intended as a primary prep stand for heavy sanding access, where multi-angle positioning can be beneficial. It is most effective as a spray-and-cure stand for efficient throughput.
Base Options and Storage
The stand is available with different base configurations depending on the workshop’s storage preference:
- Options designed to store compactly when not in use
- Options designed to stack multiple stands together for high-volume workflows
Construction
The stand is Danish-engineered and manufactured for professional collision repair use, with durable construction intended to maintain function over long-term daily work.
Typical Use
The Single Panel Stand suits shops that want multiple simple stands for spraying and curing panels quickly, keeping the workflow fast and the equipment straightforward.
Jump to: Product Highlights Jump to: Parts Processed FAQ’s
SingleFlex Classic All-in-1 Panel Stand
SingleFlex represents the traditional Flexible stand design used in workshops for many years, while EasyFlex is the newer Pro Series evolution with additional functionality.
BumperFlex Classic Bumper Stand
A simple and secure bumper stand designed primarily for painting and curing. Ideal for workshops needing a reliable solution for holding bumpers during the spray and bake stages.
Compared to MultiFlex: simpler design focused on paint and curing rather than full repair positioning.
MultiFlex Pro Bumper Stand
The Pro Series bumper stand designed for full bumper repair workflow. Multi-axis positioning allows bumpers to be adjusted easily for preparation, painting and curing on a single stand.
Compared to BumperFlex: adds preparation positioning and ergonomic adjustment for complex bumper repairs.
2PoFlex Hood / Bonnet Stand
2POFlex Hood Stand: Quick Fit Check
Best suited for
- Shops painting hoods/bonnets regularly and wanting faster, cleaner access in the booth
- Technicians frustrated by center uprights and crossbars blocking gun access
- Workflows that need a simple dedicated hood stand rather than a complex multi-adjust system
In daily use
- Single upright improves access to both sides of the hood for more consistent laydown
- Two-position setup switches quickly between upright and flat working angles
- Longer hooks hold the hood away from the upright for better gun clearance
- Folding base stores flat and clears space when not in use
Overview
The Flexible 2POFlex is a dedicated hood/bonnet stand designed for painting in the spray booth. It provides clear access to the panel so the technician can spray both sides of the hood with fewer obstructions and fewer compromises in gun angle.
When hoods are held on general-purpose stands, uprights and crossbars can block access and force the painter to work around the stand instead of focusing on the finish. The 2POFlex uses a single upright and longer hood hooks to keep the panel accessible for a cleaner, more controlled spray process.
Access and Paint Finish
The stand’s single upright design reduces the amount of structure in the painter’s way, improving reach and visibility across the hood.
The hood is held slightly further from the upright on longer hooks, which increases clearance for the spray gun and makes it easier to maintain consistent distance and angle across edges and returns.
Two Working Positions
“2PO” refers to the two working positions of the stand.
- Upright position for spraying the underside/rear of the panel
- Flat position for spraying the top/outside of the panel
This keeps setup simple and fast while still giving the painter the practical angles needed for booth work.
Workflow and Booth Movement
The 2POFlex is designed as a booth-focused tool that can be moved as needed across the workshop and into the spray area.
Durable hard rubber wheels roll smoothly and are resistant to punctures, helping the stand move reliably around busy bays and over workshop debris.
Storage and Space Saving
The stand includes a folding base so it can store flat when not in use. This helps reduce footprint in busy workshops and keeps floor space clear between jobs.
Construction
The 2POFlex is Danish-engineered and manufactured for professional collision repair use. It is built from durable nickel-plated steel for corrosion resistance and long-term reliability in daily shop conditions.
Typical Use
The 2POFlex suits shops that want a dedicated hood/bonnet painting stand that is fast to set up, simple to use, and designed around one main priority: clean access for a better finish.
Jump to: Product Highlights Jump to: Parts Processed FAQ’s
FlexTree Pro Small Parts Stand
- Paint more small parts per booth cycle without cluttering the floor space.
- Hold parts safely so they don’t get lost, dropped, or damaged between prep and paint.
- Better spray angles: remove individual holders and paint parts in-hand at any angle for a cleaner finish.
The FlexTree Pro stand is a compact, small-parts workstation that keeps mirrors, trims, caps, handles and similar pieces organised and protected while you process panels.
Instead of taping parts to benches or hanging them on wire at one fixed angle, you can lift each holder off the tree, spray at the best angle, then place it back securely.
Trim Spoiler & Mirror Kit Module
Trim, Spoiler & Mirror Kit: Quick Fit Check
For holding spoilers, mirrors, petrol-caps, door handles and some bumpers etc, if fitted with male or female threads. The spoiler kit consists of 4 stainless steal rods with 4,5,6 & 8mm male and female threads, a self-tapper for glue on spoilers, and 2 brackets for holding the rods at any angle.Best suited for
- Painting mirrors, spoilers and exterior trim pieces off the vehicle
- Technicians struggling to safely secure lightweight plastic parts
- Workshops wanting full access to both visible and hidden surfaces
In daily use
- Holds trim parts without taping or wiring them
- Allows the part to be rotated and angled while spraying
- Prevents parts falling or being touched during painting
- Keeps small visible parts protected during curing
Overview
Exterior trim components such as mirrors and spoilers are often some of the most visible parts on a repaired vehicle. However, they are also among the most difficult parts to secure safely during painting.
Without a proper mounting point, technicians typically tape, wire or balance these parts. This restricts spray access and increases the risk of touching, dropping or damaging the freshly painted surface.
Workflow Positioning
Within the Flexible Workflow System, this kit provides dedicated mounting points for mirrors, spoilers and trim components. These parts can be processed alongside larger panels while remaining securely mounted.
Controlled Holding
The Trim, Spoiler & Mirror Kit attaches directly to Flexible stands and provides secure mounting points specifically shaped for small exterior components. The part remains stable while still allowing full access around the panel.
Because the part is mounted to the stand, it moves with the stand. The technician can rotate and position the component to maintain a correct spray angle across all surfaces.
Paint Access
Many trim components must be painted on multiple sides. Holding the part by hand or securing it to a bench forces the painter to spray at poor angles.
Mounted on the stand, the part can be repositioned instead of the painter repositioning themselves. This improves coverage and reduces handling between coats.
Typical Use
The kit is used when small exterior parts must be painted off the vehicle but still require safe mounting and controlled positioning throughout the paint process.
Motorcycle Kit Module
Motorcycle Kit: Quick Fit Check
Best suited for
- Painting motorcycle tanks, fenders and similar shaped parts
- Holding curved or irregular components securely
- Workshops repairing motorcycles or specialty vehicles
In daily use
- Secures curved panels without balancing them
- Allows full spray access around the part
- Rotates the component during painting
- Reduces risk of touching fresh paint
Overview
Motorcycle components differ significantly from automotive panels. Tanks and fenders are curved, narrow and difficult to support using standard panel stands.
When unsupported, they are often held by hand, hung on wire or balanced on benches. This restricts access and creates high risk of handling damage.
Workflow Positioning
Within the Flexible Workflow System, the motorcycle kit allows stands to support motorcycle components such as tanks, fenders and wheels. This extends the same workflow principles used for automotive panels to motorcycle refinishing work.
Secure Positioning
The Motorcycle Kit attaches to Flexible stands and provides mounting points suited to narrow and curved components. The part remains stable while still allowing rotation and repositioning.
The technician can move the part instead of moving around it, allowing proper paint angle across the entire surface.
Typical Use
The kit is used whenever motorcycle parts or similarly shaped components must be painted off the vehicle while maintaining safe handling and controlled positioning.
Once you have tried it and experienced its benefits you'll never want to be without it.
Parts Processed: Motorcycle Rims, Fenders and Petrol / Gas Tanks
Double Snap-Grip Module
Double Snap Grip: Quick Fit Check
Best suited for
- Holding multiple small parts at once
- Increasing stand capacity
- Processing parts in batches
In daily use
- Provides two mounting points
- Allows painting multiple parts simultaneously
- Reduces setup time
- Improves workflow efficiency
Overview
When several small components must be painted together, technicians often lack enough secure mounting points. This causes repeated setup and handling.
Dual Mounting
The Double SnapGrip attaches to Flexible stands and provides two independent holding positions, allowing multiple parts to be mounted and painted during the same cycle.
Typical Use
Used when several small components must be processed at once without placing them on work surfaces.
Double Snap-Grip Module (Magnetic)
Double Magnetic Snap Grip: Quick Fit Check
Our Magnetic Snap Grip Tool effortlessly holds small auto body parts in need of painting, ensuring easy access and helping to produce a smooth and precise application. No more worrying about parts slipping or falling off! Featuring a magnetic base, this tool securely attaches to any metallic surface, providing a stable and reliable grip. The snap-grip head firmly holds the auto body parts in place, preventing unwanted movement and allowing you to work with ease.Best suited for
- Fast mounting of multiple small parts
- High throughput work
- Reducing repeated setup
In daily use
- Two quick mounting positions
- Allows rapid repositioning
- Prevents parts resting on benches
- Supports batch painting
Overview
Painting multiple small components typically requires repeated setup and repositioning. Improvised holding increases handling time and damage risk.
Dual Quick Mount
The Double Magnetic SnapGrip provides two rapid attachment points, allowing multiple components to be secured and processed together.
Typical Use
Used when several small parts must be mounted quickly and painted in the same cycle.
Single Snap-Grip Module (Magnetic)
Magnetic SnapGrip: Quick Fit Check
Best suited for
- Holding small components quickly
- Fast mounting without clamps or tape
- Painting small removable parts
In daily use
- Attaches instantly to the stand
- Holds small parts securely
- Allows repositioning during painting
- Prevents parts from being placed on work surfaces
Overview
Small removable vehicle components are often difficult to secure safely while painting. Improvised mounting methods restrict access and risk damaging fresh paint.
Magnetic Mounting
The Magnetic SnapGrip provides a fast attachment point on the stand, allowing small components to be secured and repositioned easily throughout the painting process.
Typical Use
The tool is used when small parts must be painted off the vehicle and need quick, repeatable mounting without complex setup.
Snap Grip Module
SnapGrip: Quick Fit Check
Best suited for
- Holding small parts during painting
- Securing lightweight components quickly
- Adding extra holding points to any Flexible stand
In daily use
- Clips parts directly onto the stand
- Allows the part to rotate with the stand
- Prevents parts being laid on benches
- Reduces handling between coats
Overview
Small automotive parts are often painted separately from the vehicle. Without proper mounting they are placed on benches, taped or held by hand.
This limits access and increases the chance of touching or damaging fresh paint.
Direct Attachment
The SnapGrip attaches directly to Flexible stands and provides a quick mounting point for small components. The part remains secure while still accessible from multiple angles.
Typical Use
The SnapGrip is used to add additional mounting capacity to a stand so multiple small parts can be processed alongside panels or bumpers.
Squeeze-Out Module
Squeeze-Out: Quick Fit Check
Best suited for
- Holding hollow components from the inside
- Painting mirror housings and similar parts
- Parts that cannot be clamped externally
In daily use
- Expands inside the part
- Holds without touching the exterior surface
- Allows full paint access
- Prevents handling damage
Overview
Some components cannot be safely clamped from the outside because the painted surface would be damaged or inaccessible.
Internal Holding
The Squeeze-Out expands outward inside the component. Instead of clamping the exterior, it holds the part from the inside walls, leaving the exterior completely accessible for painting.
Typical Use
Used when parts such as mirror housings or hollow components must be painted without external contact.
Wheel Rim Holder Module
Wheel Rim Holder: Quick Fit Check
Best suited for
- Painting wheel rims off the vehicle
- Accessing both sides of the rim
- Secure rim mounting
In daily use
- Mounts the rim from the center
- Allows full access to outer surfaces
- Rotates with the stand
- Prevents laying rims on surfaces
Overview
Wheel rims are difficult to paint when resting on benches or hung on improvised supports. Access to all sides is limited and handling damage is common.
Workflow Positioning
Within the Flexible Workflow System, the wheel rim holder secures rims from the centre hub so technicians can access the full outer surface during refinishing work. This stabilises the wheel while allowing unobstructed access.
Center Mounting
The Wheel Rim Holder secures the rim through the center opening. The outer painted surfaces remain fully accessible while the rim can be rotated and repositioned.
Typical Use
Used whenever rims must be painted off the vehicle with full access and controlled handling.
Wheel Rim Cart
Wheel Rim Cart: Quick Fit Check
Best suited for
- Workshops repairing or repainting multiple wheels
- Technicians moving wheels between prep, booth and storage
- Shops wanting safer handling of finished rims
In daily use
- Moves several rims at once without carrying
- Prevents scratches on freshly painted wheels
- Keeps wheels organised during repair workflow
- Reduces lifting and handling strain
Overview
Wheel repair work often requires rims to be moved repeatedly between removal, preparation, painting and curing. Without proper handling equipment, wheels are carried by hand or stacked on the floor, which risks damage and increases technician strain.
The Wheel Rim Cart provides a dedicated transport and staging solution that keeps rims organised and protected throughout the repair process.
Workflow Positioning
Within the Flexible Workflow System, the wheel rim cart allows rims to be transported and staged safely between preparation and refinishing areas without unnecessary lifting.
Safe Handling
Rims are sensitive to contact after preparation or painting. Placing them on the floor or leaning them against surfaces can easily scratch coatings or contaminate surfaces before curing.
The cart supports the wheels in stable positions so they can be moved without touching each other or contacting workshop surfaces.
Workflow Movement
The cart allows multiple wheels to be transported together between work areas such as preparation bays, spray booth and curing area.
This reduces repeated trips and prevents technicians from carrying heavy wheels across the workshop.
Technician Protection
Manual carrying of wheels places strain on the back, shoulders and hands, especially when processing multiple vehicles in a day.
Using the cart reduces lifting and allows controlled movement through the shop, improving safety and reducing fatigue.
Typical Use
The Wheel Rim Cart is used to transport and stage wheels safely during collision repair or refinishing, keeping them protected while maintaining an organised workflow.
◦ Danish Engineered ◦ 360 Degree Rotation ◦ Adjusts Vertically (up /down) ◦ Industrial Rubber Wheels ◦ One-Handed operation ◦ Electrogalvanized Nickel Plated Precision Steel Construction Parts Processed: Wheel Rims, All small parts with additional attachments